2010-09-15 Schmitt-Trigger IC in Smart DIL Package Schmitt-Trigger IC im Smart DIL Gehause Version 1.0 SFH 5440 Features: Besondere Merkmale: * Output: active "low" * Suitable for applications from 400 nm to 1100 nm * Available on tape and reel * Ausgang: aktiv "low" * Geeignet fur Anwendungen von 400 nm bis 1100 nm * Gegurtet lieferbar Applications Anwendungen * Optical threshold switch * Pulseformer * Counter * Optischer Schalter * Pulsformer * Zahler Ordering Information Bestellinformation Type: Ordering Code Typ: Bestellnummer SFH 5440 Q65110A1212 Maximum Ratings (TA = 25 C) Grenzwerte Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Operation temperature range Betriebstemperatur Top -40 ... 85 C Storage temperature range Lagertemperatur Tstg -40 ... 100 C Supply voltage Betriebsspannung VCC -0.5 ... 20 V 2010-09-15 1 Version 1.0 SFH 5440 Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Output voltage Ausgangsspannung VOUT -0.5 ... 20 Output current Ausgangsstrom IOUT 50 mA Total power dissipation Verlustleistung Ptot 175 mW V Operating Conditions Betriebsbedingungen Parameter Symbol Bezeichnung Symbol Supply voltage Betriebsspannung VCC Output current Ausgangsstrom IOUT Values Unit Werte Einheit min typ max 4 5 18 V 16 mA Note: A bypass capacitor, 0.1 F typical, connected between VCC and GND is recommended in order to stabilize power supply line. Anm.: Zur Stabilisierung der Versorgung wird ein Stutzkondensator (angeschlossen zwischen VCC und GND) von typ. 0.1 F empfohlen. Characteristics (TA = 25 C, VCC = 5 V) Kennwerte Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Current consumption Stromaufnahme (VCC = 5 V, E = 0) (typ) (max) Icc Icc 3.3 5 mA mA Current consumption Stromaufnahme (VCC = 18 V, E = 0) (typ) Icc 5 mA Spectral range of sensitivity Spektraler Bereich der Fotoempfindlichkeit (min) (max) 10% 10% 400 1100 nm nm Output voltage "high" Ausgangsspannung high" (IOUT = 0 mA) (min) (typ) VOUT high VOUT high 4 VCC V 2010-09-15 2 Version 1.0 SFH 5440 Parameter Symbol Values Unit Bezeichnung Symbol Werte Einheit Output voltage "low" Ausgangsspannung low" (IOUT = 16 mA) (typ) (max) VOUT low VOUT low 0.15 0.4 V V Treshold "ON" Schaltwelle ( = 950 nm, "H" "L") (typ) (max) Ee, ON Ee, ON 1700 3200 mW/m mW/m Hysteresis Hysterese (min) (typ) (max) Ee,off / Ee,on 0.5 0.6 0.9 60 Half angle Halbwinkel Rise time Anstiegszeit (RL = 280 , Ee = 600 W/cm2, = 950 nm) (typ) tr 0.1 s Fall time Abfallzeit (RL = 280 , Ee = 600 W/cm2, = 950 nm) (typ) tf 0.1 s Propagation delay time "H" "L" Ausgangsverzogerunszeit (RL = 280 , Ee = 600 W/cm2, = 950 nm) (typ) (max) tPHL tPHL 5 15 s s Propagation delay time "L" "H" Ausgangsverzogerunszeit (RL = 280 , Ee = 600 W/cm2, = 950 nm) (typ) (max) tPLH tPLH 5 15 s s 2010-09-15 3 Version 1.0 SFH 5440 Block Diagram Blockschaltbild VCC Voltage Regulator 10 k OUT + - GND OHF05594 Test Circuit for Switching and Response Time Testschaltkreis fur Schalt- und Reaktionszeit VCC VCC = 5 V R L = 280 OUT Input OUT C = 0.1 F GND R = 47 GND OHF00520 2010-09-15 4 Version 1.0 SFH 5440 Switching Time Definitions Schaltzeitdefinitionen Input 50% t PHL t PLH 90% Output 50% 10% tf tr OHF03866 Relative Threshold Relative Schwelle Ee, ON / Ee, ON (Vcc = 5 V) = f(VCC) Current Consumption Stromaufnahme ICC = f(VCC) OHF00507 E e, ON 1.5 E e, ON_5 V I CC OHF00510 6 mA 1.3 1.2 4 1.1 1 3 0.9 2 0.8 0.7 1 0.6 0.5 0 5 10 15 V 0 20 VCC 2010-09-15 0 5 10 15 V VCC 5 20 Version 1.0 SFH 5440 Output Voltage Ausgangsspannung VOUT low = f(IOUT, VCC) Total Power Dissipation Verlustleistung Ptot = f(TA) Ptot OHF01322 200 mW OHF00512 3.5 VOL V 3 160 2.5 140 120 5V 10 V 15 V 20 V 2 100 1.5 80 60 1 40 0.5 20 0 0 20 40 60 0 80 C 100 Current Consumption vs. Ambient Temperature Stromaufnahme vs. Umgebungstemperatur ICC = f(TA, VCC) I CC OHF00514 6 mA VCC = 20 V 5 VCC = 15 V VCC = 10 V 4 VCC = 5 V 3 2 1 0 -25 0 25 50 75 C 100 TA 2010-09-15 0 10 20 30 40 mA 50 I OUT TA 6 Version 1.0 SFH 5440 Package Outline Mazeichnung 2.1 (0.083) 1.9 (0.075) 0.8 (0.031) 0.6 (0.024) 4.4 (0.173) Active area 0.12 (0.005) 0.0 (0.000) 4.8 (0.189) 0.5 (0.020) 0.3 (0.012) 1.1 (0.043) 0.9 (0.035) 0.1 (0.004) 0.3 (0.012) 0.2 (0.008) 1.1 (0.043) 1.0 (0.039) Chip position VCC OUT 0.15 (0.006) 0.1 (0.004) GND 2.7 (0.106) 2.5 (0.098) GEOY6990 Dimensions in mm (inch). / Mae in mm (inch). Package 2010-09-15 Smart DIL, GND marking: broad lead 7 Version 1.0 SFH 5440 Gehause Smart DIL, GND-Kennzeichnung: breiter Anschluss 0.3 1.3 1 Recommended Solder Pad Empfohlenes Lotpaddesign 1.8 2.4 1.8 Paddesign for improved heat dissipation OHF02393 Dimensions in mm. / Mae in mm. 2010-09-15 Padgeometrie fur verbesserte Warmeableitung 8 Version 1.0 SFH 5440 Reflow Soldering Profile Reflow-Lotprofil Preconditioning: JEDEC Level 4 acc. to JEDEC J-STD-020D.01 OHA04525 300 C T 250 Tp 245 C 240 C tP 217 C 200 tL 150 tS 100 50 25 C 0 0 50 100 150 200 s 300 250 t OHA04612 Profile Feature Profil-Charakteristik Symbol Symbol Pb-Free (SnAgCu) Assembly Minimum Ramp-up rate to preheat*) 25 C to 150 C Time tS TSmin to TSmax tS 60 Ramp-up rate to peak*) TSmax to TP Recommendation Maximum 2 3 100 120 2 3 Unit Einheit K/s s K/s Liquidus temperature TL 217 Time above liquidus temperature tL 80 100 s Peak temperature TP 245 260 C Time within 5 C of the specified peak temperature TP - 5 K tP 20 30 s 3 6 K/s 10 Ramp-down rate* TP to 100 C 480 Time 25 C to TP All temperatures refer to the center of the package, measured on the top of the component * slope calculation DT/Dt: Dt max. 5 s; fulfillment for the whole T-range 2010-09-15 C 9 s Version 1.0 SFH 5440 Disclaimer Disclaimer Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version in the Internet. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components* may only be used in life-support devices** or systems with the express written approval of OSRAM OS. Bitte beachten! Lieferbedingungen und Anderungen im Design vorbehalten. Aufgrund technischer Anforderungen konnen die Bauteile Gefahrstoffe enthalten. Fur weitere Informationen zu gewunschten Bauteilen, wenden Sie sich bitte an unseren Vertrieb. Falls Sie dieses Datenblatt ausgedruckt oder heruntergeladen haben, finden Sie die aktuellste Version im Internet. Verpackung Benutzen Sie bitte die Ihnen bekannten Recyclingwege. Wenn diese nicht bekannt sein sollten, wenden Sie sich bitte an das nachstgelegene Vertriebsburo. Wir nehmen das Verpackungsmaterial zuruck, falls dies vereinbart wurde und das Material sortiert ist. Sie tragen die Transportkosten. Fur Verpackungsmaterial, das unsortiert an uns zuruckgeschickt wird oder das wir nicht annehmen mussen, stellen wir Ihnen die anfallenden Kosten in Rechnung. Bauteile, die in lebenserhaltenden Apparaten und Systemen eingesetzt werden, mussen fur diese Zwecke ausdrucklich zugelassen sein! Kritische Bauteile* durfen in lebenserhaltenden Apparaten und Systemen** nur dann eingesetzt werden, wenn ein schriftliches Einverstandnis von OSRAM OS vorliegt. *) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or the effectiveness of that device or system. **) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain human life. If they fail, it is reasonable to assume that the health and the life of the user may be endangered. *) Ein kritisches Bauteil ist ein Bauteil, das in lebenserhaltenden Apparaten oder Systemen eingesetzt wird und dessen Defekt voraussichtlich zu einer Fehlfunktion dieses lebenserhaltenden Apparates oder Systems fuhren wird oder die Sicherheit oder Effektivitat dieses Apparates oder Systems beeintrachtigt. **) Lebenserhaltende Apparate oder Systeme sind fur (a) die Implantierung in den menschlichen Korper oder (b) fur die Lebenserhaltung bestimmt. Falls Sie versagen, kann davon ausgegangen werden, dass die Gesundheit und das Leben des Patienten in Gefahr ist. 2010-09-15 10 Version 1.0 SFH 5440 Published by OSRAM Opto Semiconductors GmbH Leibnizstrae 4, D-93055 Regensburg www.osram-os.com (c) All Rights Reserved. 2010-09-15 11